3C electronics assembly
Small, thin parts and dense station spacing: frame height and the knife-edge transition decide yield.
- Knife-edge or backlit head to close the transfer gap
- Ø20–Ø30 pulleys for short machine length
- ESD and cleanroom options
Guangming, Shenzhen — Humen, Dongguan | National High-Tech Enterprise
ROBOTEK builds the motion layer of automated lines: one-piece aluminium frames, Ø20–Ø70 pulleys, six motor families and eight belt specifications, combined across 74 series. Every series ships with a 3D selection model, so feasibility becomes arithmetic.
Designed in house · national production patents · shipped to Southeast Asia, Europe and North America
01 / SYSTEM
Selection starts from the duty, not the model number: fix belt width, length and cycle time first, then drive position, belt specification and positioning method.

Head or centre drive, knife-edge, full-belt, width-specified, backlit, heavy-duty, motorized-pulley and cleated versions.

Single and dual row, motor-in-frame, width-adjustable and heavy-duty; tooth engagement gives positioning without slip.

Film-belt and chain pallet lines, plastic chain, mesh belt, single-side roller chain and small-fixture conveyors.

Timing belt modules rated 10–50 kg, self-travel modules, rotary and push rods, plus industrial rails; external dual-shaft belt drive.

90° pick-and-place, U-shape high-speed, stroke-adjustable, rotary, non-rotary and multi-lane transfer units.

82-series control box with six motor options: speed control, stepper, closed-loop stepper, induction, brushless, or no motor.
02 / MATRIX
Move the drive position on the same conveyor, change the belt profile, and the cycle time moves with it. Filter by product line below; open any model for its structure and selection notes.
The full catalogue covers 74 series with dimension drawings and speed–load curves. Models shown here are representative; ratings vary with belt width, length and motor configuration, and the confirmed drawing prevails.
03 / APPLICATION
Moving a part and moving it reliably are different problems. These are the selection priorities we see most often; the actual scheme is costed from part geometry, weight and cycle time.
Small, thin parts and dense station spacing: frame height and the knife-edge transition decide yield.
Long runs spliced from sections, where pallet location and cycle synchronisation carry the whole line.
Heavy loads, oil and continuous impact: frame rigidity and belt abrasion resistance come first.
White food-grade belts, washdown-ready structure and transitions with no dead corners.
Vision inspection and label stations need backlighting and a steady belt speed.
Curves, merges and trailer loading: whole-line interlock and maintenance you can do on site.
04 / MANUFACTURE
Shenzhen Haoyuanxing Automation Equipment Co., Ltd. is a national high-tech enterprise, headquartered in Guangming, Shenzhen, with manufacturing in Humen, Dongguan. Conveyor frames are built from high-strength one-piece aircraft aluminium; linear modules run on an external dual-shaft timing belt, customised to your load and length. The range sells throughout China and ships to Southeast Asia, Europe and North America.
Anyone can machine to a drawing.
The hard part is costing the duty first.
3-slot and multi-slot profiles extruded in one pass, then anodised; the frame doubles as guide rail, mounting face and cable route.
Speed control, stepper, closed-loop stepper, induction, brushless, or no motor; 6 W and 25 W output, gear ratios 3–180.
Economy PVC / PU, general purpose, slider, electronic parts, food, non-adhesive, and a no-belt configuration.
Conveying capacity is calculated from belt width, length, gear ratio and belt speed — not discovered after installation.
Enter belt width (B ≥ 10 mm), length (L ≥ 5 mm), motor, gear ratio and belt specification; the software builds the model and exports a 3D file straight into your line design.
Request the software05 / PROCESS
No verbal promises: each step ends with a deliverable you can check.
Part geometry, weight, cycle time, environment and installation space confirmed; unworkable options ruled out first.
Model built from belt width, length, motor and gear ratio; delivered with the conveying-capacity calculation.
Dimension drawing, option list and lead time confirmed; production starts once the technical boundary is locked.
Key stations prototyped; belt tracking, noise and positioning accuracy measured, not assumed.
Line shipped with on-site installation guidance and recommended spares by model.
07 / CONTACT
Tell us part, weight, cycle time and installation space. An engineer checks feasibility first, then quotes the model.
Guangming District, Shenzhen
Engineering, sales and selection support
Humen Town, Dongguan · 6,000 m²
Machining, assembly and factory testing
+86 150 1786 1007
sales@robotek.net.cn
Mon–Fri 9:00–18:00 (GMT+8) · WhatsApp available on this number
An AI assistant slot is reserved at the bottom right
Once a knowledge base is connected it can answer selection, pricing and lead-time questions; the panel is a demo today
AI assistant · slot reserved
The floating entry can mount your own support system — iframe, API or widget. The panel below only demonstrates the interaction.